overview

Enerdrive ePOWER Lithium B-TEC 200Ah Battery 12V - Incl Bluetooth Monitoring - K-200-DC40-BUNDLE-G2 (K200-10)

Complete System incl Battery Management System with Smartphone Monitor

*** Incl. DC to DC Charger Offer when ordered with 200BT-12V Lithium Battery ***

New Generation2 B-TECH Lithium Battery (EPL-200BT-12V-G2)

ePOWER DC2DC CHARGER incl.Two DC Inputs (e.g. Engine Charging and Solar) 10.5-32VDC Input - 40A+ 12V Output

Charges Flooded, AGM, GEL, Lithium and Custom Program

MPPT Solar Controller (Input 14.5-45VOC | ≤ 23V input, 500W (600W allowable) ≥37.5V-45V input, 750W (800W allowable))

**This is a genuine discounted offer, and with demand for lithium higher than ever. This is one of our most popular packages to date**

Bundle contains the following items:

- ePOWER B-TEC G2 12v 200Ah Lithium Battery (Battery Dimensions: 505 L x 172 W x 265 H (mm) 25.0Kg)

- ePOWER 12v DC2DC40+ charger

Available in 12v 200Ah capacity, the Enerdrive B-TEC G2 lithium battery is designed and intended for use in deep cycle applications where a single battery is required that meets the amp hour capacity.

Smartphone Monitoring System

Bluetooth Monitoring from your Smartphone or Tablet

Suits IOS and Android

The Enerdrive B-TEC G2 battery incorporates wireless Battery Monitoring Technology. By downloading the Android™ or Apple® app to your smartphone or tablet device, you can monitor the following information;

• Battery Capacity
• Battery Voltage
• Battery Current (Amps)
• Battery State of Charge (SOC)
• Battery State of Health (SOH)
• Battery Status
• Individual Cell Voltage
• Battery Temperature
• Battery Cycles
• Battery Alarms
• Battery Event Information

Battery Management System

The battery is also equipped with an internal Battery Management System that can monitor and optimise each Prismatic cell within the battery during normal operation. It will protect the battery pack from over charge, over discharge, over temperature & short circuit. The BMS helps to ensure safe and accurate operation of the battery.

specification

B-TECH Parallel Tech Note (from Enerdrive)

Paralleling of B-TEC Batteries – As you may be aware, Enerdrive have long been against the Paralleling of Internal BMS batteries. This has been from the experiences we have had and seen over the last 8 years of using Lithium’s in a commercial capacity. Although the Batteries may be able to be connected in Parallel, these batteries are not always sold with taking the application into account. From our experience due to the very low voltage difference of a lithium battery between full and 20% SOC underload. When 2 batteries are in parallel, the power doesn’t always pull evenly from each battery as the battery with the higher voltage (Lower Internal resistance) will deliver the power. For this reason, each BMS needs to be capable of handling the full load of the system. An example of the is; If 2 x 100AH Lithium batteries with an internal BMS that can handle 100A each are put into a system, the max load on the system should still be only 100A.

Both Scenarios below assume 2 x 100AH Lithium with a BMS rated to 100A each.

Scenario 1: The Consumer only runs a fridge, lights, TV and a 1000w inverter for the odd thing. They never exceed 100A load and don’t run the batteries flat. They may never have or see any Issues.

Scenario 2: The Consumer sees they have 200Ah of lithium and decide to connect a 2000w Inverter, which running at full load can be drawing approx. 180A from the battery bank. Effectively the load will not pull evenly off the 2 batteries, 1 BMS will always switch OFF before the other putting all the load on the remaining BMS, which at 180A will overload. So when the Batteries shut down like this (never simultaneously) , the Inverter will try to pull power from the remaining battery. The overloaded BMS (remaining battery) will be over run and ultimately fatigue, causing premature failure.

Normally the only place that still has power would be the solar controller output which would then inject unfiltered power into the inverter before the inverter shuts down due to a lack of power. When this occurs, in the milliseconds it takes the solar controller to realise it has no place to go, it may spike the system with solar voltage slowly damaging other equipment. By using a single Enerdrive 200AH B-TEC with the internal BMS capable of 200AH, you can then safely run your 2000w inverter without overloading the BMS. The same goes for the 200AH B-TEC, if running 2 in parallel it does not mean you can run a 3000W Combi. Due to Enerdrive not being able to know where every battery was going and into what application we decided to make a commercial decision to just do a blanket no paralleling policy for the B-TEC batteries and instead recommend people use a single battery capable of the task at hand. We still recommend this approach for internal BMS batteries, but if the installation has been deemed appropriately suited to parallel batteries (loads not exceeding rating of 1 BMS) then you will also need to be aware of the following things.

• Each battery should be charged to full separately first and left 1/2 Hr to rest and a max 0.2V difference between the batteries before connecting together (this will make sure the batteries are as close to being balanced at the start)
• Parallel cables between the batteries shall be at least the size of the Main battery cables but the larger the better.
• When connecting the Main battery cables you must make sure you cross wire the Battery Bank. .i.e. Positive to first Battery in the Bank, Negative to the last battery in the Bank (see diagram below)
• The Enerdrive B-TECH Bluetooth App (available for Apple and Android Systems) will only show 1 battery in the bank at a time and the batteries may get slightly out of sync. So make sure that you watch each battery and make sure you don’t take any one battery below its cut-out point.
• If you notice the SOC% of the batteries getting more than 10-20% out of sync, the Batteries should be separated and charged separately back to 100% and then reconnected (see first Point) to maintain the capacity of the overall Bank.
• DO NOT exceed the load limits of a single BMS.
• We also recommend that an external SOC% battery monitor is fitted for overall battery bank capacity and connect this to a Low Battery Cut-out to shut loads OFF at around 20%SOC to prevent taking any battery to its cut-out point.

For large systems that use Inverter/Charger Combi units, have large solar arrays and for people wanting to run Air-conditioning, Enerdrive still recommend upgrading to the Enerdrive White Pro Series that not only looks after the battery but the whole system by shutting down charging systems via each unit rather than just isolating the path to the Cells and also isolate loads while still allowing Chargers to access the battery. The external component approach to the White Pro systems BMS allows for infield Fault finding, service and the ability for the Enerdrive Tech team to get you out of trouble if the need arises. Other benefits of the Enerdrive White Pro System is less individual Cells, Active Balancing, Heavy duty components and a 5year Warranty that extends to the supplied Enerdrive Charging equipment and backed up by Enerdrive’s renowned Tech Support.